精品国产人妻一区二区三区免费-中本亚洲欧美国产日韩-中文字幕无码人妻aaa片-一区二区免费视频中文乱码-国产精自产拍久久久久久蜜

Welcome to HUNAN CHARMHIGH ELECTROMECHANICAL EQUIPMENT CO., LTD.!

Telephone

+86 18100733752
Website navigation
Technical articles
Location: Home > Technical articles

Causes and treatment of non suction of SMT nozzle

Publish time:2021-03-04 10:42:13   Views:

In the working process of the placement machine, due to the possible improper maintenance, we often encounter the failure of the suction nozzle of the placement machine, among which the most common problem is that the suction nozzle of the placement machine does not suck or throw materials. The problem of material throwing of SMT has been introduced in other articles on this website. Here is a special introduction to the reason why the suction nozzle of SMT doesn't suck material and the treatment method. There are four main reasons why SMT nozzle does not suck material. I hope it can help you a little.


1、 Due to the internal reasons of the mounter equipment, the suction nozzle of the mounter does not suck material


On the one hand, the suction nozzle of the placement machine is lack of vacuum negative pressure. Before the suction nozzle takes parts, it automatically switches the mechanical valve on the mounting head from blowing to real adsorption, which produces a certain negative pressure. When the negative pressure sensor detects the value within a certain range after the parts are absorbed, the machine is normal, on the contrary, the suction is poor. Generally, the negative pressure at the suction nozzle from the pick-up position to the mounting position should be at least 400mmhg, and the negative pressure of the mounting large device should be above 70mmhg, so the filter in the vacuum pump should be cleaned regularly to ensure sufficient negative pressure; at the same time, the working state of the negative pressure detection sensor should be checked regularly. On the other hand, the filter on the mounting head and the filter on the suction nozzle are blackened due to the pollution and blockage of the surrounding environment or the impure gas source. Therefore, the filter should be replaced regularly. Generally, the filter on the suction nozzle should be replaced at least half a month, and the filter on the mounting head should be replaced at least half a year, so as to ensure the smooth flow of air.


2、 The suction nozzle of placement machine does not suck material due to external reasons


On the one hand, it is the pressure relief of the air source circuit, such as the aging and fracture of the rubber pipe, the aging and wear of the sealing parts, and the wear of the suction nozzle after a long time of use. On the other hand, it is the large amount of waste generated by the adhesive or the dust in the external environment, especially the paper tape packaging components after cutting off, which results in the blocking of the suction nozzle of the mounter. Therefore, it is necessary to check the cleanliness of the suction nozzle every day and monitor it at any time In order to ensure the good condition of the suction nozzle, it is necessary to clean or replace the clogged or defective suction nozzle in time. At the same time, it is necessary to ensure the correct and firm installation when installing the suction nozzle, otherwise the suction nozzle or equipment will be damaged.


3、 The problem of SMT suction nozzle itself leads to no suction


For example, the suction nozzle of the placement machine is deformed, blocked, damaged, resulting in insufficient air pressure, air leakage, resulting in poor material suction, improper material taking, and identification without material suction or throwing. The suction nozzle of the placement machine should be maintained and corrected regularly.


4、 Because of the feeder failure of the placement machine, the suction nozzle of the placement machine does not suck material


Poor feeding of the feeder of the placement machine will lead to deformation and rust of the cover plate, spring and other operating mechanisms, which will lead to component deviation, vertical piece or failure to absorb the device. Maintain and correct the feeder regularly.

Copyright ? 2013-2023 HUNAN CHARMHIGH ELECTROMECHANICAL EQUIPMENT CO., LTD.

RecordNo.:XiangICPB18021313-1  Xiang gong wang An bei no.43019000201475

Addr:104-604 Building D, Jindao Industrial Park, No. 179 Huizhi Middle Road,Changsha High-tech Development Zone, Changsha City,Hunan Province,CN

Telephone:+86 73185504084 / WhatsApp : +8618100733752 / WeChat : 86 18100733752 / Skype : 86 18100733752

Mailbox:one@charmhigh.com / sales@charmhigh.com

Youtube

oiz780
oiz780
已為您復制好微信號,點擊進入微信
oiz780
oiz780
已為您復制好微信號,點擊進入微信
主站蜘蛛池模板: 又黄又猛又爽大片免费| 人人妻人人澡人人爽欧美一区九九| 18禁亚洲深夜福利人口| 天天爽夜夜爽人人爽一区二区| 天天鲁一鲁摸一摸爽一爽| 国产放荡av剧情演绎麻豆| 青草视频在线播放| 欧美乱人伦视频在线| 婷婷四房综合激情五月在线| 久久久久国产a免费观看rela| 亚洲最大无码av网站观看| 久久久亚洲综合久久久久87| 亚韩无码一区二区在线视频| 97资源共享在线视频| 国产真实露脸精彩对白| 任你躁国产自任一区二区三区| 国产在线精品视频你懂的| 亚洲最大av一区二区三区| 无码国产一区二区三区四区| 成人性生交大片免费看r老牛网站| 无码无遮挡在线观看免费| 日韩av人人夜夜澡人人爽| 国产裸拍裸体视频在线观看 | 男人女人做爽爽18禁网站| 成人国产mv免费视频| 亚洲内射少妇av影院| 亚洲精品无码永久在线观看性色| 伊人久久精品一区二区三区| 亚洲精品日韩中文字幕久久久| 97夜夜澡人人爽人人喊中国片| 五十老熟妇乱子伦免费观看| 国产成人亚洲综合无码dvd| 在线观看免费人成视频| 亚洲∧v久久久无码精品| 老熟妇乱子伦牲交视频| 欧美 亚洲 国产 另类| 亚洲人成在久久综合网站 | 亚洲日韩欧美内射姐弟| 熟妇人妻中文av无码| 天堂va欧美va亚洲va好看va| 久久久国产精品va麻豆|